Flowcrete Flowshield ESD SL 19.33kg Kit Gloss Finish Resin Flooring System - Requires 700g Epoxy Pigment
Flowcrete Flowshield ESD SL (2mm)
An antistatic, hard-wearing, abrasion resistant, self-smoothing gloss finish resin flooring system. Meets EN IEC 61340-5-1 antistatic standard requirements.
Typically used in sensitive environments such as electronic, laboratory, defence and cleanroom environments.
Pigment sold separately — requires 700g Epoxy Pigment per 20kg system.
Product Benefits
- Attractive: Brightens and enhances workspace environments
- Antistatic: Meets EN IEC 61340-5-1 antistatic standard requirements
- Hygienic: Seamless finish, easy to clean and maintain
- Hard-wearing: Provides a durable, abrasion resistant floor finish
Technical Profile
| Property | Standard | Value |
|---|---|---|
| Fire Resistance (CHF Value) | AS/ISO 9239.1 | 6.6 kW/m² |
| Fire Resistance (Smoke Value) | AS/ISO 9239.1 | 398% (Mean) |
| Slip Resistance | AS4586-2013 | P1 Rating |
| Temperature Resistance | — | Softens over 60°C |
| Water Permeability (Karsten Test) | — | Nil (Impermeable) |
| Abrasion Resistance (Taber Abrader) | 1kg load, CS17 wheels | 80mg loss per 1000 cycles |
| Compressive Strength | BS6319 | 60 N/mm² |
| Flexural Strength | BS6319 | 40 N/mm² |
| Tensile Strength | BS6319 | 25 N/mm² |
| Bond Strength (Pull-Off Test) | ASTM D4541 | >1.5 MPa |
| Electrical Resistance | EN IEC 61340-5-1 | <1 x 10⁹ Ω |
Speed of Cure
| Traffic Type | 10°C | 20°C | 30°C |
|---|---|---|---|
| Foot Traffic | 36 hours | 24 hours | 16 hours |
| Vehicular Traffic | 72 hours | 48 hours | 36 hours |
| Full Chemical Cure | 12 days | 7 days | 7 days |
System Design
| Layer | Product | Coverage Rate |
|---|---|---|
| Layer 1 | Flowprime AU (+ Conductive Tape grid) | 0.2 kg/m² |
| Layer 2 | Flowprime ESD Conductive | 0.08 kg/m² |
| Layer 3 | Flowshield ESD SL | 3.6 kg/m² |
Available Colours
Available in 9 AS2700 standard colours: Bluebell, Bridge Grey, Dark Grey, Light Grey Blue, Light Grey, Mushroom, Serpentine, Straw, and Terracotta. Applied colours may differ from examples shown. Not all pigments are stocked as standard and may be made-to-order. For a full colour chart and samples, contact your local Flowcrete office.
Note: Due to the incorporation of conductive materials, actual finished floor colour and finish may be affected. This variation may be more evident in lighter colours.
Substrate Requirements
Concrete or screed substrate should be a minimum of 25 N/mm², free from laitance, dust and other contamination. Substrate should be dry to 75% RH as per ASTM F2170 (AS1884:2012). Slab on ground concrete must have an effective damp proof membrane in place.
Application & Mixing
Application and curing temperatures: 5–35°C. Ready-mixed product should be used within 20 minutes at 20°C. At higher temperatures, application time is shorter. The system is not UV stable and will discolour unless otherwise stated.
Storage
12 months in unopened packs. Store between 5°C and 35°C. Should be stored inside and protected from frost, weather, moisture, direct sunlight and contamination ingress.
Manufacturer
Tremco CPG Australia Pty Ltd
63 Radley Street, Virginia QLD 4014
Phone: +61 7 3205 7115
Email: [email protected]
- Epoxy Floor Coatings ,
- Epoxy Flooring
No reviews found