Dribond Monoflex 20kg Rubber Modified Tile Adhesive

$38.18
($42.00 inc gst)
High-strength, highly flexible, premium, non-slump/lipping, economical and multipurpose.
Same Day Delivery

To Metro Melbourne.

Order before 1pm for Same Day Delivery

3-Hour Express Delivery
Online Only
Shipping time and rates:
Malvern
BrandsDribond Consumtion20kg covers 10m²+ using a 10mm notched trowel (floors) Product TypeRubber Modified Tile Adhesive Size20kg DeliverySame Day
Description

Dribond Monoflex 20kg Tile Adhesive

High-strength, highly flexible, premium, non-slump/lipping, economical and multipurpose.

Description

A premium, water-resistant, flexible, rubber-based, fast-setting, cementitious adhesive for bonding ceramic and stone tiles to porous and non-porous surfaces subject to vibration and thermal movement.

Features

  • C2 high bond strength, exceeds 1MPa
  • S2 exceptional flexibility deformation, exceeds 5mm
  • E extended open time
  • T non-slump
  • A one-pack with two-pack performance, i.e. 1.9MPa adhesion > 5mm deflection
  • Will withstand thermal and vibration movement and 1.0mm shrinkage cracks
  • Exceeds the requirements of AS ISO 13007.1
  • Ideal for fixing granite, porcelain & vitrified tiles
  • For fixing tiles to fibre cement sheet over timber floors
  • Suitable for shower alcoves
  • Ideal for new concrete floors subject to shrinkage cracks
  • Tiling over existing tiles

Uses

A one-pack, thick or thin bed, internal and external floor and wall flexible adhesive for fixing over most substrates, e.g. concrete, heated concrete slabs, cement render, fibre cement sheets, plasterboard, existing properly prepared ceramic tiles, vinyl tiles and Construction Chemicals waterproof membranes. Not suitable for immersed or swimming pool application. Do not use directly over timber floors (Construction Chemicals provides other systems).
Performance Data
Exceeds the performance requirements
of AS ISO 13007.1.
Tensile adhesion strength
1.9MPa (28 days)
Coverage (Approximate)
20kg will cover 10m2 + using a 10mm notched
trowel (floors).

Specification

The ceramic tile adhesive will be a water-resistant, fast-setting, flexible, rubber-based, polymer-modified cement that conforms to AS ISO 13007.1 and has a minimum tensile adhesion strength of 1.9MPa, such as Monoflex manufactured by Construction Chemicals and shall be applied in accordance with the manufacturer’s application instructions.
Surface Preparation
The surface to be tiled must be firm and clean, free from dust, waxes, paint and other contaminants. Steel floated concrete floors must be mechanically roughened, washed thoroughly and allowed to
dry prior to tiling. Prime with Primax on external
and smooth surfaces and Primebond on internal porous surfaces.
A guide to tile joint sizes
Internal minimum 2mm, external minimum
4mm or as specified by the tile manufacturer
and AS3958.1. Do not fix tiles with tight joints. When grouting joints of less than 3mm we recommend mixing the grout with Primebond. Greater care is needed to place the grout deep
into joints before pointing the joints to compact
the grout surface.

Mixing

Mix with clean water using 3-4 litres to 10kg.
Add the powder to the water while mixing with a slow speed electric drill to obtain a lump-free creamy consistency. Adjust mix to suit users preference. Pot life is approximately 2 hours.
Allow to stand 5 minutes and re-stir before use.
Application
Apply with a notched trowel. For tiles 400mm x 400mm or greater use a 12mm notch and butter tile back (as per the Australian Standard AS3958.1). The final bed thickness must not be less than 2mm for walls and 3mm for floors, to accommodate movement. Spread about 1 metre at a time.
Tiles must be set in place while the adhesive is still wet on the surface. Press tiles firmly into the adhesive using a slight sliding motion. Tiles must be firmly bedded into the adhesive so no voids occur beneath the tiles. Do not spot fix. Movement joints (5mm) to be at 5 metre grids, corners and room perimeters are filled with Colour Seal or Sealflex.

Grouting

Grout when the tile bed has hardened so tiles can not be dislodged and the adhesive has set (approximately 8-12 hours). Use Kemgrout mixed with Primebond.

Set Time

Approximately 8-12 hours, depending on temperature, humidity and surface porosity.
Allow longer for dense tiles and cooler conditions.
When using externally or in shower alcoves protect the adhesive for 7 days (23°C @ 50% relative humidity) to allow the adhesive to fully cure before putting into use. Do not tile when rain is imminent.
Safety Precautions
Non-toxic, but contains cement which contains silica. Wear gloves and appropriate respirator. Further information for this product is
contained in the Safety Data Sheet.

Features

Consumtion
20kg covers 10m²+ using a 10mm notched trowel (floors)
Product Type
  • Rubber Modified Tile Adhesive
Size
20kg
Delivery
Same Day
Reviews

No reviews found

How TradieCart Works
Order online or by phone

TradieCart Confirms Your Order

Fast Same Day Delivery

Save Time. Save Money.
Trade Products Shipped by TradieCart in 2-3 Hours.

Your favorite products from your favorite Trade Stores. Shipped by TradieCart.
More Products
  • Similar Products
  • Recently Viewed
  • Purchased Together
  • Most Popular
  • Bestsellers
 
 
 
 
 
More products that ship together